Device Setup Parameters - Edge (preview)
Preview of the consolidated setup-parameters page. Temporary.
Some edge device models need a little setup after they're claimed before they start reporting. In almost every case this is a set of parameters — a username and password, an SNMP community string, a port, or a device ID — that you enter once in Xyte.
Until those parameters are set, the device won't send telemetry — its page shows "This device isn't reporting data yet." A device that answers on the network can still show as reachable/online; the missing parameters are a separate state, flagged as Missing Credentials.
How to enter the parameters
Both routes open the same Add credentials dialog, which shows the parameters that specific model needs.
From the Devices table (bulk — devices with the same requirements)
- Go to Devices and select one or more devices that need the same parameters. A device that still needs its parameters shows Missing Credentials. If your selection mixes devices with different requirements — or includes devices that need no credentials — the Add Credentials button is disabled, with the tooltip "You can only bulk add credentials to devices that require credentials and have identical requirements." (This is usually the same model, but different models with identical parameters work too.)
- In the action bar at the bottom, click Add Credentials.
- Fill in the parameters and Save — it applies to every selected device.
From a single device's page
- Open the device. While setup is pending, its overview shows the "This device isn't reporting data yet" banner.
- Click ⋯ → Edit to open the same Add credentials dialog.
- Fill in the parameters and Save.
Once saved, the device starts reporting on its own — that is your confirmation it worked.
Some values come from the deviceA few parameters are generated or enabled on the device itself first — e.g. turning on SNMP (Cisco switches), generating an authentication code (Sony BRAVIA), or reading the display ID (Samsung). Get the value from the device, then enter it in Xyte.
Browse by vendor
Pick a vendor to open its model families and their exact parameters.
Acer· 1 model family
These Acer models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Barco· 1 model family
These Barco models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password
Applies to:
- ClickShare v2
Parameters
- Username (optional)
- Password (optional)
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
BenQ· 1 model family
These BenQ models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Biamp· 2 model families
These Biamp models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password, Port
Applies to:
- TesiraLUX Series
- Tesira Text Protocol (TTP)
Parameters
- Username (optional) — The user name used for authentication when connecting to and retrieving data from the Tesira device.
- Password (optional) — The password used for authentication when connecting to and retrieving data from the Tesira device.
- Port (optional) — An optional field specifying the network port on which the Tesira Text Protocol (TTP) service is accessible. If not provided, the default TTP over SSH port is used (22).
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
BrightSign· 1 model family
These BrightSign models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password, Protocol
Applies to:
- Series 5
Parameters
- Username (optional) — Username used for authentication. Usually its admin.
- Password (optional) — Password user for authentication.
- Protocol (required) — Protocol which should be used in API communication.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Canon· 1 model family
These Canon models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Casio· 1 model family
These Casio models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Christie· 1 model family
These Christie models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Cisco· 5 model families
These Cisco models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
SNMP community string
Applies to:
- C9300
- CBSx series
Parameters
- SNMP community string (required) — Community string used for reading values via SNMP protocol
On the device firstEnable SNMP on the device and set a read-only community string, then enter that same string here.
The Add credentials dialog for these models shows exactly these fields:
Username, Password
Applies to:
- Room Bar
- Room Kit (EQ, EQX, Pro)
- Room Navigator
Parameters
- Username (required)
- Password (required)
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Crestron· 16 model families
These Crestron models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password
Applies to:
- 4 Series
- AirMedia Series
- CEN-ODT-C-POE
- Crestron Flex Conferencing Kits
- Crestron Flex Phones
- Crestron Flex Soundbars
- Crestron Mercury
- DM Matrix Switchers
- DM-NAX Series
- DM-NVX-DIR Series
- DM-NVX Series
- HD-MD 4KZ AV Switchers (REST)
- IV-SAM Series
- TSS/TSW 4-Series Touch Panels
- TS/TSW 60 Series Touch Panels
- UC Engine
Parameters
- Username (required)
- Password (required)
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Epiphan· 1 model family
These Epiphan models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password
Applies to:
- Pearl Series
Parameters
- Username (required)
- Password (optional)
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Epson· 1 model family
These Epson models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Extron· 1 model family
These Extron models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Select Specific DXP Model, Port, Password
Applies to:
- DXP HD 4K PLUS
Parameters
- Select Specific DXP Model (required)
- Port (optional) — Fill this field if the device is using a non standard port
- Password (optional) — Fill if device is password protected.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Fujifilm· 1 model family
These Fujifilm models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Gude· 1 model family
These Gude models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password, HTTP protocol
Applies to:
- Gude device
Parameters
- Username (optional) — Username used for authentication
- Password (optional) — Password used for authentication
- HTTP protocol (optional) — HTTP protocol used when communicating with the device
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Hitachi· 1 model family
These Hitachi models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
HP Poly· 1 model family
These HP Poly models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password
Applies to:
- Poly Studio Series
Parameters
- Username (required) — Username used for authentication.
- Password (required) — Password user for authentication.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
InFocus· 1 model family
These InFocus models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Kiloview· 2 model families
These Kiloview models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password
Applies to:
- N50/N60
- N5/N6
Parameters
- Username (required) — Username used for authentication
- Password (required) — Password used for authentication
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Logitech· 2 model families
These Logitech models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password
Applies to:
- Logitech CollabOS
- Rally Bar Series (All-in-One Video Bars)
Parameters
- Username (required)
- Password (required)
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Maxell· 1 model family
These Maxell models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Mitsubishi· 1 model family
These Mitsubishi models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Netgear· 1 model family
These Netgear models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Telnet Port, Telnet User Name, Telnet Password
Applies to:
- M4250 AV Line Series Switches
Parameters
- Telnet Port (required) — Enter Telnet port (usually 23)
- Telnet User Name (required) — User name for login to switch (usually admin)
- Telnet Password (required) — Admin password for login to switch
On the device firstEnable Telnet on the switch and use its admin login — Telnet user name (usually
admin), the admin password, and port (usually23).
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Novastar· 1 model family
These Novastar models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Project ID, Use encryption, Secret
Applies to:
- H series
Parameters
- Project ID (required) — ID of the project configured in device settings which will be used in API authentication
- Use encryption (required) — Describes if we should use encryption or not in authentication process.
- Secret (optional) — Secret key that will be used in API authentication
On the device firstCreate or open the project in the device/vendor settings and copy its Project ID and secret — used for API authentication.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Panasonic· 9 model families
These Panasonic models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password, Port
Applies to:
- All-in-one dvLED
- Display
- DLP Fixed Lens
- DLP Interchangeable Lens
- MZ Series 10K-
- MZ Series 10K+
- Projector
Parameters
- Username (optional)
- Password (optional)
- Port (optional)
The Add credentials dialog for these models shows exactly these fields:
Password, Port
Applies to:
- Displays (PJ Link Enabled)
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Ricoh· 1 model family
These Ricoh models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Samsung· 2 model families
These Samsung models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Display ID
Applies to:
- QMC Series
- WMR Series
Parameters
- Display ID (optional) — If Display ID was set for screen it is needed to establish driver communication. Otherwise default ID (0) is used.
On the device firstIf a Display ID was set on the screen (via the remote menu), enter that number here. If not, the default
0is used.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Sennheiser· 1 model family
These Sennheiser models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password
Applies to:
- TeamConnect Bar Series
Parameters
- Username (optional) — Username used in REST API communication
- Password (optional) — Password user for REST API communication
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Sharp· 1 model family
These Sharp models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Sharp NEC· 1 model family
These Sharp NEC models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Sony· 2 model families
These Sony models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Authentication Code
Applies to:
- Pro BRAVIA
Parameters
- Authentication Code (required) — Set the authentication code in Network Settings on the TV
On the device firstOn the display, open Network Settings and set/enable the authentication code, then enter it here.
The Add credentials dialog for these models shows exactly these fields:
Password, Port
Applies to:
- Projectors (PJLink Enabled)
Parameters
- Password (optional) — Provide the password if enabled for this projector
- Port (optional) — Fill this field if the projector is using a non standard port
On the device firstOn the projector, turn on PJLink / network control and set a PJLink password if one is required. Leave Port blank unless it was changed from the default
4352.
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
VSI· 1 model family
These VSI models need parameters entered in Xyte after they're claimed. Families that need the same parameters are grouped together below.
Username, Password
Applies to:
- PacketAV 4/5 Encoder & Decoder
Parameters
- Username (required) — Default: admin
- Password (required) — Default: admin
The Add credentials dialog for these models shows exactly these fields:
Where to enter them
Both routes open the Add credentials dialog shown above.
From the Devices table — select one or more devices that need these same parameters (they show Missing Credentials), then click Add Credentials in the action bar. The button is enabled only when every selected device has identical requirements (usually the same model):
From the device page — open the device (it shows the isn't reporting data yet banner), then ⋯ → Edit:
Once saved, the Missing Credentials flag clears and the device starts reporting — your confirmation it worked.
Updated 2 days ago